lab dip approval for activewear, color fan decks and fabric swatches laid out side by side on a design table

Lab dip approval for activewear: how to lock in your color before production

How Pantone numbers, lab dips, light sources and dye lots work in activewear, and what you write down so the color you approved is the color that arrives on the roll.

Lab dip approval for activewear runs in four steps: you pick a color number from a physical textile fan deck, your supplier dyes small swatches of your own fabric in that color, you judge them next to your reference under two different light sources, and you sign off one swatch with a date on it. Until that approved swatch is sitting with you and with your factory, all you have is a color code in an email, and there is nothing in that to hold anyone to.

I ran my own sportswear brand, PIXIE, for 23 years with in-house design and production. Color is the subject I have had more discussions about than any other, and it is almost never because a supplier did poor work. It is because hardly anyone starting a line has been shown how color behaves in textiles yet.

Why the color on your screen is worth nothing

You design a bra in a deep petrol. On your monitor it is exactly right. You send the image over, your supplier says yes, and three weeks later a sample lands that leans blue green.

That is not a supplier failing you. There was never anything specific to work from. Your screen emits light and fabric reflects it, which are two completely different ways for a color to reach your eye. On top of that every monitor is calibrated differently, and your JPEG has traveled through three mail servers and a compression step. That is why the apparel industry works with physical references, something you can hold, lay side by side and ship.

What does a Pantone number actually do?

A number from the textile fan deck is your starting point. It is an agreed language: when you say 19-4517 TCX, a dyer on the other side of the world knows which color you mean without you sending anything.

Use the textile version, not the print version. The TCX and TPG codes belong to the textile system, where TCX is printed on cotton and TPG on paper, while the C and U numbers are for graphic printing. That difference gets missed a lot. Pantone lays out the textile color systems and what each one is used for on its own site.

A Pantone number points your supplier in the right direction and then stops being useful, because the same dye lands differently on polyester than on cotton, and differently again on a brushed surface than on a smooth one. That is where the lab dip comes in.

What is a lab dip?

A lab dip is a small piece of your own fabric, dyed to the color you specified. Your supplier usually makes a few with small variations and sends them to you. You pick one, or you send them all back with a note that it needs to go deeper or duller.

It sounds like a detour, and it is the cheapest insurance in your whole production. A lab dip costs you a little time and sometimes a small fee. A full run in a color you did not sign off can take your margin, your delivery date and the studio owner who preordered for her members. Always ask for the dip on your own quality, not on the dye house standard cloth, otherwise you are approving a color on a fabric you will never use.

How do you judge a lab dip?

This is where most new brands slip, because they hold the swatch up at the kitchen window and form an opinion. Do it this way instead:

  • Lay the lab dip directly against your Pantone reference, edges touching, with no white space between them.
  • Judge it in daylight, or better, in a light box with standardized daylight.
  • Then look at it again under your normal indoor lighting.
  • Turn the swatch a quarter turn. On fabrics with a texture or a nap, the color reads differently in the other direction.

That second light source matters more than it sounds. Two colors can match perfectly in daylight and drift apart under store lighting. The effect is called metamerism, and it is why a customer in a fitting room sometimes sees something you never saw on your own table. You cannot always solve it, and you can see it coming if you check under two kinds of light.

Why the same color lands differently on two fabrics

Say you are building a set: a bra in a smooth knit and a legging in a heavier brushed quality. Same Pantone, same dyer, same dye batch. You will still see a difference, because of fiber and surface. Polyester takes a different dye class than cotton, and a rough surface scatters light in every direction so it reads duller, while a smooth surface reflects more directionally and reads deeper. How fiber and construction drive this is covered in choosing the right fabrics for sportswear and in the breakdown of polyester in activewear.

If you need two qualities to work next to each other, say so explicitly. Ask for lab dips on both fabrics at the same time and judge them as a pair. Skip that and you will approve two separate colors that are each fine alone and wrong together.

What is a dye lot and why do you record it?

Fabric is dyed in batches. Each batch, or dye lot, carries its own number, and two batches of the same color are rarely identical. Usually the gap is small enough that nobody notices, until a legging from lot A hangs next to a bra from lot B. Three things you do about that:

  • Buy enough fabric in one go for your whole run, including the reorder you are hoping for.
  • Record the batch number on every delivery and keep a dated swatch.
  • Cut panels that sit next to each other from the same batch. Two sleeves from two lots is a return waiting to happen.

This ties straight into your supplier’s minimums. How much you have to take per color decides how many colors you can afford, and that is a conversation you have up front.

What goes in your tech pack?

All of the above belongs on paper. Per style and per colorway you record:

  • the color name you use and the Pantone number with the correct extension;
  • which quality that color applies to;
  • the date the lab dip was approved and who approved it;
  • the color of everything that has to match, such as thread, zippers, elastic, binding and drawcord.

That last point gets forgotten almost every time. You get your fabric dyed perfectly and then a zipper arrives that sits just off. Build it into your activewear tech pack from the start, and mark it on your technical flat drawing so there is no doubt which part you mean.

Will your color hold up over time?

An approved color tells you how your fabric looks today, and nothing about how it looks after twenty washes, a season of chlorine or a summer of sun.

There are tests for that: colorfastness to washing, to light, and to crocking, which is color transferring when the fabric rubs. Your supplier can usually supply those reports. Ask specifically on darks and on brights, because that is where the risk sits. A deep black legging that marks a light sofa is a complaint that lands on your brand directly. If you also want certainty about the dyes themselves, ask for certification such as OEKO-TEX STANDARD 100, where the textile is tested against a list of harmful substances and the certificate runs for one year.

Lab dip approval for activewear, step by step

  1. Pick your color from a physical textile fan deck, using a TCX or TPG number.
  2. Request lab dips on your own quality, and on both qualities if two have to match.
  3. Judge them against your reference, edges touching, under daylight and under indoor light.
  4. Approve one swatch with a date and a name on it, keep a copy, and record the dye lot number on every delivery that follows.

It reads like extra work on a page. In practice it is what makes your pieces hang together on a rack, which is how people start recognizing your brand from across a room.

Inside Start Your Own Sportswear Brand I walk you through this whole route, from your first color card to the agreements you make with your factory. If you want to see where color sits in the bigger picture first, start with the 10 steps to your own sportswear brand guide.

Do I need a Pantone fan deck to get started?

For your first exploration, no. As soon as you are talking to a supplier, yes, because you need a physical reference you can both hold. A fan deck is an investment that lasts years, as long as you store it out of the light. Fan decks fade, so keep it in a drawer and not on a windowsill.

What is the difference between a lab dip and a strike-off?

A lab dip is a trial dyeing of a solid color on your fabric. A strike-off is a trial print of a pattern on your fabric. With a print you are judging more than color: you also check the scale of the design, the repeat size and how the print feels on the hand, which matters a lot on stretch fabrics.

How many rounds of lab dips are normal?

It varies by supplier and by color. Difficult colors such as a clean black, a true red or a precisely matched nude often take more rounds than an average mid tone. Agree the turnaround per round up front, because that is what decides whether your delivery date stays realistic.

Can I approve a color from a photo my supplier sends?

No. A photo passes through a camera, a screen and a compression step before it reaches your eye. At best you can tell that something is clearly off. Approval only happens with the swatch in your hand, next to your reference, under two light sources.

Share the Post: